Hauptkategorie: Mod's

Arduino UNO Mini Limited Edition

Die Miniatur Version des Arduino UNO´s:

Im November 2021 wurde zur Feier von 10 Millionen verkaufen Arduino´s die Limited Edition des Arduino UNO´s vorgestellt.

Wie auf dem Arduino UNO arbeitet hier ein ATmega328P, jedoch in der SMD Version. Genauer gesagt im QFN Gehäuse. Dazu gibt es einen USB-C Anschluss, und achja, er ist nur 1/4 so groß cool

Kommentar schreiben (0 Kommentare)

Schneeflocke mit RGB LED´s

Ein Schmuckstück als Platine, die mit Sensoren die Umgebung erfasst und mit RGB LED´s und Ton reagieren kann laughing

[ESP32, Arduino Nano 33 BLE Sense, WS2812, KiCad]

Weiterlesen ...

Kommentar schreiben (0 Kommentare)
Hauptkategorie: Mod's

Arduino I2C multiple slaves

Arduino multiple I2C slaves

Connecting more than 1 I2C device to an Arduino is simple, if you follow some basic rules.

I2C Basics

The I2C bus is designed to be a multipoint serial connection system.
So it was always intended to use with multiple devices.

But how can they share the same Pins on the Arduino?

Here is a simple layout:


The µC Master is the Arduino, with multiple I2C Slaves connected over the SDA and SCL Lines.

The Trick is within the 2 pullup Resistors Rp!

I2C pullup resistors

They are needed to help the devices with getting the slew rates it needes. Depending on the i2c bus speed different rise times are needed.

In Standard mode with 100khz a maximum rise time of 1000ns is ok, for fast mode with 400khz the rise time should not exceed 300ns.

If want to just get it going, take 4.7k and it will work when you have just 1 slave.

But we want to make it right or?

The size is depending from the total capacitance in the circuit, so you will have to look to the datasheets and sum up the capacitance to get our Cb, next look up the formula:

Rp(max) = tr/0.8473 x Cb

Where tr is our allowed rise time for the signal, take this with 1µs or 300ns depending on your bus speed.

See also the TI Application note: SLVA689 I2C Bus Pullup Resistor Calculation

So what? What happens when the resistor is wrong?

I2C wrong pullup resistor

I2C wrong pullup resistor

if the resistor is to high the signal rises to slow, that will cause missing bits -> trouble.

But also to low values get you trouble, they will draw too much current, do not go below 1k.

Good practice is to first make the calculations, then hook up a oscilloscope and verify your values.

I2C bus slave address conflict

Every slave must have a unique address, so check your datasheets and ensure that the devices all have unique addresses!


I2C Bus with mixed Voltages

mixing 5V and 3V devices is possible, but dont just connect them together!

I2C Level shifter(AN97055)

It needs a bidirectional level shifter, common practice is to use Mosfets with clamping diodes.

Take a look at the Application Note 10441 from NXP it is about "Level shifting techniques in I2C-bus design"

Also the old Application Note AN97055 "Bi-directional level shifter for I2C-bus and other systems." is a more in depth read about it.


NXP AN10216 I2C Manual

Silabs AN0011 I2C Master and Slave Operation

TI SCAA106 Troubleshooting I2C Bus Protocol

DSScircuits Effects of varying I2C pullup resistors

NXP AN10441 Bidirectional level shifter for I2C

Phillips AN97055 Bi-directional level shifter for I2C-bus and other systems


Kommentar schreiben (0 Kommentare)